当前位置:首页 > 开发 > 操作系统 > 正文

Fedora14命令行下的拨号连接

发表于: 2011-02-20   作者:czmmiao   来源:转载   浏览次数:
摘要: 1:下载 system-config-network-1.5.94-2.fc10.noarch.rpm和system-config-network-tui-1.5.94-2.fc10.noarch.rpm,并同时安装:rpm -Uvh 包1 包2; 2:首先确认你的网卡正常工作,让他处于自动获取IP状态,启动linux终端(root权限),因为fedora10下已经自带有pppoe的安装文件,可以

1:下载 system-config-network-1.5.94-2.fc10.noarch.rpm和system-config-network-tui-1.5.94-2.fc10.noarch.rpm,并同时安装:rpm -Uvh 包1 包2;

2:首先确认你的网卡正常工作,让他处于自动获取IP状态,启动linux终端(root权限),因为fedora10下已经自带有pppoe的安装文件,可以直接输入如下命令,要想理解各个步骤是什么意思,那就看英语咯,我这里就不多解析了。

[root@localhost ~]# pppoe-setup ---------------这里开始安装PPPOE

Welcome to the PPPoE client setup. First, I will run some checks on
your system to make sure the PPPoE client is installed properly...


LOGIN NAME

Enter your Login Name (default root): xy170638010214
---------------这里键入上网拨号的帐号

INTERFACE

Enter the Ethernet interface connected to the PPPoE modem
For Solaris, this is likely to be something like /dev/hme0.
For Linux, it will be ethX, where 'X' is a number.
(default eth0):
---------------这里按回车键

Do you want the link to come up on demand, or stay up continuously?
If you want it to come up on demand, enter the idle time in seconds
after which the link should be dropped. If you want the link to
stay up permanently, enter 'no' (two letters, lower-case.)
NOTE: Demand-activated links do not interact well with dynamic IP
addresses. You may have some problems with demand-activated links.
Enter the demand value (default no):
---------------这里按回车键

DNS

Please enter the IP address of your ISP's primary DNS server.
If your ISP claims that 'the server will provide dynamic DNS addresses',
enter 'server' (all lower-case) here.
If you just press enter, I will assume you know what you are
doing and not modify your DNS setup.
Enter the DNS information here:
---------------这里键入 server 也就是自动获得DNS

PASSWORD

Please enter your Password:
---------------这里键入上网拨号密码
Please re-enter your Password:
---------------这里键入上网拨号密码

USERCTRL

Please enter 'yes' (three letters, lower-case.) if you want to allow

normal user to start or stop DSL connection (default yes): ---------------这里键入 yes


FIREWALLING

Please choose the firewall rules to use. Note that these rules are
very basic. You are strongly encouraged to use a more sophisticated
firewall setup; however, these will provide basic security. If you
are running any servers on your machine, you must choose 'NONE' and
set up firewalling yourself. Otherwise, the firewall rules will deny
access to all standard servers like Web, e-mail, ftp, etc. If you
are using SSH, the rules will block outgoing SSH connections which
allocate a privileged source port.

The firewall choices are:
0 - NONE: This script will not set any firewall rules. You are responsible
for ensuring the security of your machine. You are STRONGLY
recommended to use some kind of firewall rules.
1 - STANDALONE: Appropriate for a basic stand-alone web-surfing workstation
2 - MASQUERADE: Appropriate for a machine acting as an Internet gateway
for a LAN
Choose a type of firewall (0-2): 0
---------------这里键入 0

Start this connection at boot time

Do you want to start this connection at boot time?
Please enter no or yes (default no):y
---------------这里键入 yes

** Summary of what you entered **

Ethernet Interface: eth0
User name: xy170638010214
Activate-on-demand: No
DNS addresses: Supplied by ISP's server
Firewalling: NONE
User Control: yes
Accept these settings and adjust configuration files (y/n)? y
---------------这里键入 y
Adjusting /etc/sysconfig/network-scripts/ifcfg-ppp0
Adjusting /etc/ppp/chap-secrets and /etc/ppp/pap-secrets
(But first backing it up to /etc/ppp/chap-secrets.bak)
(But first backing it up to /etc/ppp/pap-secrets.bak) 

Congratulations, it should be all set up!

Type '/sbin/ifup ppp0' to bring up your xDSL link and '/sbin/ifdown ppp0'
to bring it down.
Type '/sbin/pppoe-status /etc/sysconfig/network-scripts/ifcfg-ppp0'
to see the link status.

[root@localhost ~]# pppoe-start ---------------激活PPPOE设备,成功后会自动返回

[root@localhost ~]# pppoe-status ---------------查看PPPOE状态
pppoe-status: Link is up and running on interface ppp0
6: ppp0: <POINTOPOINT,MULTICAST,NOARP,UP,LOWER_UP> mtu 1492 qdisc pfifo_fast state UNKNOWN qlen 3
link/ppp
inet 113.14.36.24 peer 113.14.32.1/32 scope global ppp0
---------------这里有IP分配给你了,可以知道你已经成功登录这个帐号了。我们ping下百度IP看看 通了,所以可以上网咯。
[root@localhost ~]# ping 121.14.88.14
PING 121.14.88.14 (121.14.88.14) 56(84) bytes of data.
64 bytes from 121.14.88.14: icmp_seq=1 ttl=54 time=17.7 ms
64 bytes from 121.14.88.14: icmp_seq=2 ttl=54 time=17.7 ms
^X^C
--- 121.14.88.14 ping statistics ---
16 packets transmitted, 16 received, 0% packet loss, time 15895ms
rtt min/avg/max/mdev = 17.675/17.744/18.170/0.175 ms
[root@localhost ~]# pppoe-status
pppoe-status: Link is up and running on interface ppp0
6: ppp0: <POINTOPOINT,MULTICAST,NOARP,UP,LOWER_UP> mtu 1492 qdisc pfifo_fast state UNKNOWN qlen 3
link/ppp
inet 113.14.36.24 peer 113.14.32.1/32 scope global ppp0
[root@localhost ~]#


以下是对PPPOE的基本操作


使用:

拨号上网 pppoe-start
段开上网 pppoe-stop
查看状态 pppoe-status

3:要开起NetworkManager服务;

参考至:http://blog.csdn.net/gshshaohui/archive/2009/05/02/4142677.aspx

如有错误,欢迎指正

邮箱:czmcj@163.com

Fedora14命令行下的拨号连接

  • 0

    开心

    开心

  • 0

    板砖

    板砖

  • 0

    感动

    感动

  • 0

    有用

    有用

  • 0

    疑问

    疑问

  • 0

    难过

    难过

  • 0

    无聊

    无聊

  • 0

    震惊

    震惊

编辑推荐
本文主要介绍一些GPRS管理与创建APN拨号连接相关的知识点。新建拨号连接利用RAS实现,本文将详细介
原文: http://www.cnblogs.com/michael-zhangyu/archive/2009/07/04/1516797.html 本文主要介绍一些
PS:我费了一两个小时写的好好的一篇文章发布的时候提示有非法字让修改,但是去修改的时候版面全变
PS:我费了一两个小时写的好好的一篇文章发布的时候提示有非法字让修改,但是去修改的时候版面全变
PS:我费了一两个小时写的好好的一篇文章发布的时候提示有非法字让修改,但是去修改的时候版面全变
本文源自:http://blog.sina.com.cn/s/blog_7c72b4210100qu6r.htmlp 学校里宿舍用的是联通宽带,赠
今天笔记本上开发再次遇到这个问题,经过确认eclipse indigo版本和ibus1.3.11确实有冲突。具体表现
今天笔记本上开发再次遇到这个问题,经过确认eclipse indigo版本和ibus1.3.11确实有冲突。具体表现
记录了 CentOS 最小化安装后如何配置和连接无线网络,当时的情况是路由器使用的WEP加密方式,所以设
原文地址:http://www.blackmoreops.com/2014/09/18/connect-to-wifi-network-from-command-line-in-
版权所有 IT知识库 CopyRight © 2009-2015 IT知识库 IT610.com , All Rights Reserved. 京ICP备09083238号